How to make a solution for soap bubbles. Soap bubbles: recipe with and without glycerin. Soap bubbles at home. High strength soap bubbles

Almost every person at least once in his life tried to make soap bubbles from improvised means (most often in childhood

Let's note a few things:

the size of the bubbles that people call large varies greatly for different viewers (most consider 50-60 cm in diameter to be something exotic)
the size of the bubbles depends both on the composition and, no less, on the design and materials of the devices, as well as human skill.
On the Internet, on various trinket-free sites, a dozen primitive recipes are written as carbon copies, based on dishwashing detergents, soap, glycerin and other improvised means, with the help of which you can really easily blow bubbles half a meter in diameter, which most people consider large.

But for those who find these sizes too small, look deeper! It is unlikely that anyone will tell you a universal recipe; in any case, you will have to experiment with concentrations.

For those who crave really huge bubbles, several meters in diameter, we’ll give you an important clue - these are water-soluble polymers, that’s the secret! Glycerin and sugar, of course, also help (it’s difficult without them), but only up to a certain concentration - if higher, it gets worse!

Try gelatin, egg white, polyvinyl alcohol, etc. But the best thing (and this is recommended by many professionals) is cellulose ethers (hydroxypropyl methylcellulose and hydroxyethylcellulose) or CMC, which is available to all. It can also work very well with gelatin.

The rest of the additives are a matter of taste and goals. Experiment and you will succeed!

As for impure glycerin, don’t be alarmed; most often in pharmacies it is simply diluted with water to 70% concentration in order to save money and deceive the buyer...

Cellulose ethers are absolutely not dangerous to health (we often eat them with ice cream, sauces, candies and pills...) Unfortunately, it is not so easy for the average person to get pure hydroxyethylcellulose in small quantities, but products that contain it in sufficient quantities are quite accessible .

Here is the simplest bubble recipe that kids will love:

(please note that the composition is given in grams! For glycerin and other additives, the density is not equal to unity, everything must be weighed!)

Fairy - 150g (it is better to take yellow or green)
Glycerin (99%) - 50 g or 70 g -70% from the pharmacy
Gel lubricant - 100g (or 0.2 g of QUALITY CCM - the thicker and more transparent the resulting gel, the better quality)
Water up to 1 kg

Preparation: mix gel lubricant or CMC thoroughly and slowly without whipping with glycerin, add fairy, bring to 1 kg with warm (almost hot) boiled water (ideally distilled); after cooling, the composition is ready for use.

A carpet beater is an excellent tool for blowing bubbles (the inner rings and patterns are cut out with a hot knife, leaving only the outer hoop with a handle). The handle heats up near the hoop itself and bends at 45 degrees. to make it easier to dip into a bowl of solution. The rim of the beater is tightly wrapped around the entire circumference with a thin cotton rope to hold more solution.

The solution is very sensitive to the presence of grease, dust, etc., so take the trouble to keep it clean (pre-wash basins, hands, equipment...)

Pleasure guaranteed!

this is the basic composition... you can add various additives to it to further improve it, but each additive has its own...

By the way, besides fairies, there is little that is suitable for normal bubbles, so take only this - it’s already a proven option! if you get pure hydroxyethylcellulose, then the dosage is the same as for CMC (0.2 g per liter of solution “+/-” 0.1 g) - the dosage must be strictly observed, because if there is a lot of it, the bubbles will not blow out well and burst quickly.

Polyvinyl alcohol comes in different viscosities and methods of dissolution (soluble in cold and hot water). Its percentage, just like for CMC, fluctuates within tenths of a gram per liter of solution, and exactly how much needs to be selected for each brand separately.

It is recommended to make a 10% solution of PVA in water (this makes it easier to dose): heat the required amount of water to 80-90 degrees in a water bath, quickly stirring, pour PVA into the water, preventing the granules from sticking together. With constant stirring in a water bath, the granules dissolve in 20-40 minutes (depending on the brand and size of the granules).

Store the resulting solution in the refrigerator, because it is susceptible to spoilage by microorganisms, or prepare small quantities immediately before use (more preferable, since some brands of PVA change all viscosity and properties when storing solutions, especially in cold conditions).

Having a basic composition for bubbles, gradually increasing the concentration of PVA using the selection method, you can easily find the optimal option.

There's actually a wiki on giant bubbles and a ton of public recipes. It's even on YouTube. by keywords giant bubbles.

The composition is close to jamble juice and others. That is, ferri, water, PEO and PEC and specifically: Poli-ox (polyethylene oxide) and Natrosol 250HHR CS. The problem is different. It is impossible to obtain consistent results. The same composition sometimes works, sometimes it doesn’t. Depends on a bunch of conditions and the location of the stars. In addition, modern feri is overfilled with thickeners.

How to blow giant soap bubbles

First we will make a soap solution. We will need: Some container. Water (1 l.). Detergent (eg Fairy) or shower gel (eg Palmolive) (150-200 ml). A little glycerin, which can be bought in pharmacies (25 ml.). (Optional) Personal lubricant, non-oil based, also available from pharmacies (25 ml). Two sticks of any size, but to be sure, let them be 30 cm. Cotton rope, about 50 cm.

For long-lasting bubbles, the water must be soft, preferably distilled. Heat the water and pour it into your container. As a container, it is better to use one that has a wide lid so that our inflatable device can be lowered there freely. If you use a glass container, remember that hot water must be poured into it gradually, warming up the walls of the container, otherwise it will burst. How easy it will be to blow bubbles depends on many parameters, in particular the air humidity in the area where you live. Therefore, if you want to achieve the ideal composition, pour the shower gel into the water in several portions, each time checking whether your solution has improved. If you are impatient, you can mix 150 ml at once. gel with water, bubbles can be inflated even with non-ideal composition. Add 25 ml to the solution. glycerin and 25 ml. lubricant (you can do without lubricant) and stir everything thoroughly. Make sure that no foam forms when stirring. If it does appear, you can remove it with a spoon. Test the solution by blowing a bubble through a straw. Don't worry if the bubbles are still normal. The secret to huge bubbles isn't just the soap solution recipe. Feel free to add gel or other ingredients if you want to experiment.

Now you need to make an inflatable device. It consists of two sticks, between which a rope is tied so that it forms a triangle. It is best to blow bubbles outside in calm weather (or with a slight breeze). Lower the inflator into the solution, then lift it up and begin to move back. The resulting air flow will inflate the bubble. Have fun, and feel free to experiment!

Secrets of creating big soap bubbles

1. Composition, recipe for large soap bubbles (BMP).

The main components have not been secret for a long time. In Europe, this is Fairy liquid soap; I use non-concentrated soap, preferably without perfume additives (but this is not necessary), 10% of the volume of the solution. In America they use DAWN brand soap. Glycerin - 5 - 10% of the solution volume. Polymers. I tried different ones and settled on J-Lube Gleitgel Pulver. It is a PEO with a very high (important) molecular weight. 1 - 1.5 grams of powder per liter of solution. With this polymer, the stool will inflate and fly. As well as some additives that improve the solution. Read more on the Soap Bubble Wiki Ingredients website (you need to translate a dozen words from English or enter the text into one of the online translators). This is the best variant. I would like to add. Take distilled water, and not from the nearest well. And Fairy is real, not bottled in the basement around the corner.

2. Why don't I get bubbles?

You bought an expensive foreign factory powder or solution from local professionals, but there is no bubble. And he won’t pout. Because most often we have no instructions or understanding in this not entirely simple matter. Usually people want to please themselves on a warm, sunny day. And for a normal bubble you need a temperature preferably no higher than 20°, humidity no lower than 60% and shade. Bubbles do not tolerate high temperatures and dryness. More than 50 different videos on YouTube show that the conditions were either created or were suitable. I carried out experiments with various solutions only in the morning. However, if you have a good solution and the right tools, and most importantly - experience, you can surprise children and friends in the worst weather conditions (for bubbles).

3. The tool is important.

You can find samples of it on YouTube. The triangle for launching bubbles should be made of natural, moisture-absorbing material. Wool, linen and others. Use a triangle divided into four sectors. What does this give? A complex of small stuck together bubbles appears, each of which is more tenacious. The stocking turns out to be up to two - four meters long and lasts up to 5 - 7 seconds after tearing off, which is enough to admire, and for children - to pierce it. In unfavorable (for bubbles) weather, you can use a rope with 5 - 8 small triangles. The result is small, but more stable bubbles and a lot of them. But this requires experience. The entire instrument is, of course, homemade.

How to make giant soap bubbles

To obtain large soap bubbles or many smaller bubbles, film-forming compositions are used - solutions of surfactants in composition with alkanols, high-molecular additives and electrolytes. In these compositions, water, glycerin, glycols, polyglycols and other liquids, as well as mixtures thereof, are used as solvents. The use of non-aqueous solvents having a boiling point higher than the boiling point of water can improve the color, stability and elasticity of the film. The water content of the composition is usually in the range of 10-99%, the content of non-aqueous solvents can reach up to 90%. Anionic surfactants are used as surfactants in the composition - primary and secondary alkyl sulfates, alkyl sulfonates and anionic derivatives of nonionic surfactants, for example, ethoxylated alkanols, in which the hydrogen atom of the -OH group is replaced by the -OSO3Na group. The quantitative content of surfactants is 0.2-10% by weight of the composition. To improve the consumer properties of the composition and give the composition the necessary viscosity and elasticity of the film, primary and secondary alcohols with the number of carbon atoms n = 8-15 or narrower fractions, for example, with n = 12-14, as well as soluble in contains high-molecular compounds, in particular cellulose derivatives - methylcellulose, carboxymethylcellulose, hydroxyethylcellulose, etc. The content of alkanols and cellulose derivatives is 0.1-2 wt.% each.

Various salts are used as electrolytes, changing the solubility of surfactants and other components of the composition, or/and stabilizing the pH of the surfactant solution, and affecting the viscosity and surface tension of the film. The concentration of electrolytes in the composition can reach up to 30 wt.%. In addition to these components, the composition usually contains a preservative.

Example. The film-forming composition for blowing soap bubbles contains, in wt.%:

Water - 47
Glycerin - 47
Sodium alkyl sulfonate - 4.5
Sodium tetraborate - 0.7
Methylcellulose - 0.5
Mixture of alkanols n=12 - 0.2
Preservative - 0.1o

Recipe for making soap bubbles for the show

15 parts distilled water
0.5 parts glycerin
2 tablespoons lemon juice
1 tablespoon bicarbonate of soda
1 teaspoon J-Lube (J-lube is a concentrated sexual lubricant in powder form, which consists of 75% sucrose and 25% polymers)

Second recipe

A slightly different proportional composition for soap bubbles:

12 parts distilled water
1 part Fairy ultra liquid detergent
0.5 parts glycerin
0.25 hours Polyvinyl alcohol
2 teaspoons Metylan glue (see photo below)
1 teaspoon J-Lube

Third recipe

You need: 6 cups of distilled water, half a cup of dishwashing gel, half a cup of cornstarch, 1 tablespoon of baking powder and 1 tablespoon of glycerin.

Experience: Dissolve corn starch in water, mix in the remaining ingredients. We mix well, but try not to create foam. Leave the mixture alone for about an hour. From scrap items we make frames of any shape for dipping into liquid.

What happens: Our bubble can live for a while and swell to enormous sizes due to surface tension. However, you can’t just make a bubble out of water; you need to increase the surface tension using various additives.

Big soap bubbles. Recipes

How to make big soap bubbles.

As a child, whoever dabbled in soap bubbles? Launching them with a straw or straw from the balcony. However, time passes, progress moves. And on the Internet (rarely on the street) you can see a show of soap bubbles or just huge bubbles. Soap bubbles up to 2 meters in size or trains of bubbles 2 - 4 meters in size shimmer with all the colors of the rainbow, flash in the sun, leaving an unforgettable impression. Adults become children for a moment, and children rejoice.

Is it possible to make big bubbles? It is possible, but this is not a very simple matter and requires not only money, but also time. And if the matter can be solved with money, then with patience and time - not always.

Let's start with the recipes.

Look on the Internet by searching for “soap bubbles” and you will find hundreds of recipes. Most of them are repeated, shamelessly copied from each other. There will be about two dozen left. Verified down to the gram, they are often monstrously different from each other.

However, a general pattern is visible.

1. Simple solution.

Fairy detergent (Spülmittel) – 150 – 200 ml. (You can try replacing Fairy, but the result may not be the best.)
Glycerin – 25 – 50 ml. (Increases the durability of the soap bubble).
Sugar (Traubenzucker) – 1 tablespoon. (Sugar and glycerin can be replaced with sugar syrup. However, if there are midges or wasps present, I would advise using a little more glycerin, without the sugar.)
Gelatine – 1-2 teaspoons of the solution from the following recipe.

Under the conditions described below, this recipe produces small, reliable bubbles.

2. The recipe is budget-friendly and produces fairly large bubbles.

Water (destilliertes Wasser) – up to 1000 ml.
Fairy detergent (Spülmittel) – 100 – 120 ml. (Mostly 10% of the amount of solution).
Glycerin – 30 ml.
Sugar (Traubenzucker) – 1 tablespoon. (I used grape sugar, but this is not necessary. Sugar can be replaced with glycerin, and glycerin and sugar with simple syrup.)
CMC wallpaper glue solution (Tapetenkleister) - 100 – 150 ml. (Wallpaper glue CMC - the packaging says - the composition is Carboxymethylcellulose - or the sodium salt of this substance, known as a food additive - E 466. So - dissolve a level teaspoon in 300 - 400 milliliters of cold or warm water and several times during the day stir until completely dissolved. 100 - 150 ml of this solution and use. The solution can be stored for 4 - 5 days, no more).
Gelatine solution - 2 – 3 teaspoons. (Dissolve 3 grams of gelatin in 50 ml of water in a water bath. Let it cool a little, add to the solution. Start with 2 teaspoons. Gelatin improves soap bubbles, but if you overdo it, you will get jelly.)
Gelatine can be replaced with a small amount of Xanthan Gum (food additive E415 - xanthan gum).

Under the conditions described below, this recipe, which I have tested, gives, depending on the tool used - a frame - a triangle, stable soap bubbles up to one and a half meters.

This solution should not be stored. (The glue may lose its viscosity, and the sugar and gelatin may deteriorate.) It is better to pour it out 3 – 4 days after its creation.

You can experiment a little with the solution. The amount of glycerin can be doubled. If you use a little more gelatin, you can reduce the amount of CMC wallpaper glue or vice versa.

3. Third solution, For larger bubbles.

Water (destilliertes Wasser) – up to 1500 ml.
Fairy detergent (Spülmittel) - 130 – 150 ml. (10% of the amount of solution is optimal)
J – Lube Pulver – lubricant – 1.5 – 2 grams.
Glycerin – 50 – 100 ml.
Baking soda (Backpulver – Natron) – 1.5 – 2 g. per liter of solution.
Citric acid (Zitronensäure) – 1 g. per liter of solution.

To reduce the fluidity of the solution, you can add up to 0.8 g per liter of Xanthan Gum solution (food additive E415 - xanthan gum) or gelatin.

Under the conditions described below, this is a better and more all-weather solution. The chemical that works wonders in this solution is the polymer that makes up 25% of this powder - Poly-ethylene-oxide (PEO) or (PEG-90M) with a molecular weight of more than 35,000. The remaining 75% is sucrose, which prevents the polymer from sticking together and improves dissolution in water. A relative of this polymer, Poly-ethylen-glykol (PEG), with a lower molecular weight, is not as effective.

J – Lube Pulver – dissolve in a small amount of water in the largest possible jar in the microwave, as it has the bad property of foaming like milk and running away. It can be dissolved in a water bath and even in hot water, which will take more time. Wash your hands and dishes easily with water or dry table salt. A 284 gram jar of this powder is enough for at least 200 liters of solution. Therefore, at a price of 20 euros per jar, the price of a liter of solution will be small.

The amount of lubricant, soda and acid must be observed quite accurately. You can ask to weigh it at the pharmacy or on simple homemade scales, using coins of 1, 2, 5 cents or kopecks as weights. Baking soda and citric acid are dissolved separately in a small amount of water to form sodium citrate, and then added to the solution.

Soda and citric acid make soap bubbles better.

Replacing Fairy with another detergent will worsen the solution. Americans use their own non-concentrated or concentrated liquid soap - Non-Concentrated Classic Dawn and Dawn Professional and others.

Any solution will become better if, after preparation, it stands in a cool place for a day. It should be stirred well two to three times. In total, a small party with children and adults can take up to 4 - 5 liters.

A possible replacement for polymer (PEO) or J – Lube Gleitgel Pulver, but not always equivalent – “Macrogol” - E1521 (PEG) with the highest possible molecular weight (perhaps it needs 3 - 4 times more than J-Lube). And also DOW WSR301 (PEO), Hydroxy-ethyl-cellulose (HEC) - brand name - Natrosol-250 HX, DOW Cellosize QP100MN, KY Gleitgel, KY Jelly Lubricant, Sylk Glietmittel Gel, Hydroxy-propyl-methyl-cellulose (HPMC) – E464, SurgiLube, HPMC K15M (DOW), Methocel-Cellulose Ethers. Information about these chemicals is available on the Internet, and the dosage of these polymers can be found on English-language websites by entering in the search window - “soap bubble”, “ingredients-soap bubble Wiki”, “bubble formula”, “bubble magic”.

Don't you know English? Happens. There are a dozen publicly available translator programs on the Internet. They translate poorly from English into Russian, but it’s quite possible to figure out the recipe.

There are more than 50 original videos on YouTube. You will find them by asking in the search window – “Soap bubble show” or “giant soap bubbles”.

You can and should experiment with the amount of substances in recipes.

Now about the important stuff.

Safety precautions.

Do not blow soap bubbles near roads with traffic. Children or dogs may run onto the road after the bubbles. A person driving may look at the soap bubbles and drive into the wrong place. This is fraught with big trouble. The remains of a bubble that gets on an expensive suit, although it will not ruin it, can lead to a scandal. In the room where soap bubbles are blown, be sure to lay a film on the floor. It will not be easy to clean the floor from the solution.

Conditions under which the solutions work.

The film of a soap bubble is thin. And therefore it is very sensitive to humidity (or dryness) of the air. In good, dry, sunny weather, the bubbles often do not inflate and immediately burst. And no solution, even the most secret, even the most expensive, will help here. It is better to blow soap bubbles in calm or weak wind, cool, humid weather. In the morning or late afternoon. Better in the shade. It works well on the seashore or river bank. After rain or even if it drips a little.

Humidity can drop quickly. It is important that the air is clean, free of odors and dust, midges and tree pollen. Although, for some reason, debris that gets into the solution often does not interfere. However, a moped passing nearby can stop your experiments by puffing up air. There should be no draft or operating air conditioners in the room.

The water for the soap solution must be distilled. After checking the resulting solution, you can experiment with local water.

The tool you use to make bubbles is important. Without a good tool, without experience and skills, you shouldn’t start demonstrating it to friends. The inflation device consists of two sticks or bamboo sticks (or fishing rods, between which a rope is tied, forming a triangle. It is better to use a rope made of natural material - wool, cotton or flax, as they are more moisture-absorbing. These materials accumulate more solution. The rope may consist of several threads with a total diameter of up to 4 millimeters or more. It is advisable to wrap rings with a handle with wool or other thread.

It's fun to use a fan to blow bubbles. It is common knowledge, but not everyone knows, that moist air at the same temperature is lighter than dry air. And in weather with little humidity, the moist air should raise the bubble. You can try using a fan to dry your hair, filling a soap bubble with warm air. By carefully watching bubble show videos on YouTube, you will discover many secrets. For the most advanced, it’s a good idea to keep a notebook where you can write down the composition with which you are currently experimenting, the weather - the presence or absence of sun, time of day, humidity (It would be nice to have a hygrometer or psychrometer. You need to measure humidity, of course, outside.), the wind and its strength. and direction. (In the mornings it sometimes blows up the slope, which makes launches inconvenient). And also note the approximate diameter of the ball, the length of the stocking and the lifetime of the soap bubble.

However, the main secret and basis of success is your time invested in this exciting business.

If you truly love entertainment, then this will be interesting for you, because games with a soap bubble evoke not only wild delight and interest in children, but also in adults. When blowing soap bubbles, I always dreamed that the soap bubble would not burst, but it turned out that the life of the soap bubble ended in the prime of life, when it could still fly and fly.

What you need to organize games with a soap bubble:

1.Water

1.Empty container

3.Tube

4. Soap solution

5. Wool glove

Sequencing:

1.Make a soap solution

2. We put on a glove

3. Blow a bubble

4. We are happy with the result.

Despite its simplicity, the process of making soap bubbles has several secrets that you need to know. For example, it is worth knowing that for soap bubbles NOT It is advisable to use hard water. Chilled boiled water is ideal, to which you need to add shampoo or liquid soap. In this case, the concentration should be 1:10. This figure is not strict, but it is also not advisable to overdo it.

If you are going to make soap bubbles for a small child, you should consider using baby shampoo that will not cause irritation if it accidentally gets into the eyes. One of the secrets to big, strong bubbles is the addition of gelatin or glycerin.

Recipe for making homemade soap bubbles

There are several ways.

The easiest way to make bubbles at home

Take 100 ml. dishwashing detergents
Add 50 ml. glycerin and 300 ml. water
Stir thoroughly and you're done!

Recipe for making non-bursting bubbles

Recipe one

Let me clarify right away that to receive the finished mixture you must wait at least three days, so you should prepare in advance for a walk that involves such entertainment. So, first we prepare the water. Regular tap water will not work. The fact is that it contains impurities of salts, and salts, in turn, make the bubbles inelastic. No matter how hard you try, you will not be able to blow out a large bubble from a solution made with ordinary water. This is why it is better to use distilled water. Measure out 600 milliliters and bring the water to a boil.

Then add 300 milliliters of regular glycerin, which can be purchased at the nearest pharmacy, to boiling water, 20 drops of ammonia (sold there), and then add 50 grams of powdered detergent (cleaning or washing powder).

Mix the solution thoroughly so that all ingredients are completely dissolved in it.

There will still be some sediment at the bottom, but that's normal. Cover the resulting solution with a lid and leave for two to three days at room temperature. Don't forget that children are curious creatures, so keep the container with the solution out of reach of little hands. After this period, the solution should be thoroughly filtered by passing it through a piece of gauze folded in three or four layers. And we wait again, but we already store the filtered solution in the refrigerator. After 12 hours, you can pour it into a bottle and go for a walk. Of course, this recipe cannot be called easy to prepare, but the result is worth it. The bubbles from it turn out to be large, do not burst for a long time and shimmer in different colors.

Recipe two

To prepare a solution for this recipe, we will need 800 milliliters of water (remember that it must be distilled), 200 milliliters of any dishwashing detergent, 100 milliliters of glycerin and 50 grams of gelatin and sugar. First, pour boiling water over the gelatin so that it swells. Drain off the excess water, add sugar to the gelatin and dissolve the mixture over low heat, avoiding boiling. After this, pour in all the water, detergent and glycerin, mix. Please note that you should mix very carefully so that foam does not appear on the surface of the solution. From such a solution it is possible to blow strong and large bubbles. And the ingredients in it are practically safe, if you do not take into account the dishwashing detergent, which I am prejudiced against.

Recipe three

The good thing about these bubbles is that you can touch them. With light contact with hands and even water, they remain unharmed. To prepare such a solution, you need to combine 100 milliliters of transparent lubricant (this is a reason to overcome shame when visiting a sex shop))), 200 milliliters of dishwashing detergent (preferably with a thicker consistency) and 100 milliliters of glycerin. Add 800 milliliters of boiling water to the mixture, stir, but without forming foam. The solution can be immediately poured into the bottle.

There are several ways that, while still preparing the solution, will help you determine whether you are doing it correctly. The first is to blow a small (about 30 millimeters in diameter) bubble and time the time during which it does not burst. If it lasts for half a minute, then the solution is good. You can check it another way. Touch the blown bubble with a finger moistened with the same solution. If the bubble does not burst, it means you have prepared the solution correctly.

"Tool" for creating huge bubbles

A classic straw, of course, will not work in this case. You can tie a woolen thread to two wooden skewers of the same length, and then moisten it generously in a soap solution. By vigorously moving and spreading the skewers, the inventors of this design obtain large soap bubbles. Neither my husband nor I got anything out of this venture except a bunch of splashes. Another idea, borrowed from the Internet, justified itself. You will need a cord about 150 centimeters long, a large bead and two sticks. First, we tie a cord to the end of one stick, thread the bead at a distance of 75 centimeters from the knot, and then tie the same end of the cord to the other stick. We tie the remaining end of the cord to the first knot. The result is a design of two sticks, between which a cord in the form of a triangle with a weight bead is stretched.

We dip the cord in the soapy solution, let it soak thoroughly, and then straighten the sticks with outstretched arms. Please note that sudden movements are excluded, but you won’t be able to make bubbles too slowly, since the solution from the cord will simply drain to the ground.

A walk with such a “toy” will definitely be appreciated by your children. And not only yours, because huge bubbles cannot help but attract attention. And further. For a walk, I recommend dressing your children in clothes that you don’t mind ruining, because I haven’t yet been able to remove stains from bursting bubbles so that not a trace remains.

Video on how to make soap bubbles

Interesting facts about soap bubbles

Mentions of the first soap bubbles were seen in frescoes found during excavations in the city of Pompeii. These frescoes depicted children with soap bubbles;

If you blow a soap bubble in severe frost (-25 C), it will quickly freeze in the air, acquiring an almost ideal spherical shape, and will break when it hits the ground;

There are many artists who delight the public with their main work - creating soap bubbles of various sizes and shapes.

Soap bubbles will be strong thanks to glycerin, which makes the shell of the soap bubble stronger.

In childhood, many had fun with one thing: buying a bottle of solution and blowing soap bubbles. These funny balls were flying everywhere. It was a fascinating activity, so interesting that we didn’t even notice how the bubble ended... Let's discuss how to make soap bubbles at home.

It's time to remember childhood fun and fully enjoy soap balls. You don’t need to rush to the toy store to buy a soap solution; you can easily prepare it yourself at home. Basic components can be found in any home:

Glycerin or sugar.
Water.
Soap.

How to make your own soap solution at home

There are many recipes for making soap bubbles, which differ in composition and method of preparation. Choose a recipe whose ingredients can easily be found at home. Or prepare the components for a special soap solution in advance. I suggest you see how to cook the classic version.

As you can see, everything is quite simple. If you can’t find a jar of glycerin at home, you’ll have to walk to the pharmacy.

Cooking method:

Take a piece of laundry soap and rub it on a grater. Instead of a grater, you can use a knife, choose what is more convenient.
Pour hot water over the soap and stir the solution with a spoon until the soap is completely dissolved. In the process, you can chuckle with a villainous laugh.
Do not bring the solution to a boil! The water should be hot, but not boiling!
If a few pieces of soap are left floating in the saucer, strain the solution through cheesecloth.
Last step. Pour glycerin into the resulting liquid.

Don't forget to prepare the tool you will use to blow bubbles. A stick from a store-bought bottle of soap bubbles will do. Often at home they use a straw, which is also very convenient. Or you can roll a circle of the desired diameter from wire found in the garage. Now you are ready to blow bubbles of any size!

Video recipe

Soap bubble solution like store bought

In addition to the classic method, there are many other recipes for making bubbles. Let's say you want to make a soap solution like you would buy in a store. In this case, let’s study the table with the composition for making a store-bought version.

It is better not to use tap water. It degrades the quality of the bubbles! Use the dishwashing liquid you usually use.

As soon as you find corn syrup at the store, you can start making soap bubbles. Ready?

Preparation:

Boil water and pour into a bowl.
Pour dish liquid into a bowl and stir.
Add corn syrup and mix well.

Ready. You are awesome. You can leave the solution for two to three hours to infuse, and then start having fun by encouraging your friends to take part.

Video tips

DIY soap bubbles with glycerin

Are you intrigued? Did you like the idea and want to continue experimenting with bubbles? Well, the classic recipe is not the only one that uses glycerin.

Recipe with washing powder

I want to warn you that it may take several days to prepare a solution with washing powder. If you are ready to make sacrifices, read the instructions.

Step-by-step instruction:

Warm up the water. Do not bring to a boil.
Add washing powder and mix. The powder should completely dissolve.
Pour glycerin and ammonia into the solution. Stir.
Let it brew for at least two days. More is possible.
Strain the solution through cheesecloth and place the container in the refrigerator overnight.

If you do everything right, the results will pleasantly surprise you.

Recipe for big soap bubbles

The method is a little more complicated than the previous ones, but the result will be more interesting, because the bubbles will come out more than one meter!

Take either distilled or boiled water. If you want to make more liquid, just maintain the proportions.

How to do:

Dissolve the gelatin in a bowl of water, then strain the excess water through cheesecloth.
Add sugar. All that remains is to melt it. Do not heat the liquid to boiling point!
Take the resulting liquid and add it to the prepared water.
Add glycerin and dish soap next. Stir the resulting solution. Be careful! No foam should form in the liquid.

Ready! Now you can please your loved ones with bubbles of a new scale!

Recipe for long lasting big bubbles

The second way is to make a liquid from which you can get meter-long bubbles.

Filtered or distilled water works great. Use thicker dishwashing liquid. Use lubricant without impurities, we are just creating a solution for bubbles.

Preparation:

Mix all ingredients except water.
Heat the water and pour into the solution.
Mix thoroughly, but not too much. Foam should not appear on the surface of the liquid.

The solution is ready! The result was so-called “especially tenacious” bubbles. They will not burst even after contact with water. I advise you to try them in action right now!

Homemade recipe without glycerin

If you don’t have glycerin on hand, it doesn’t matter. The bubbles, of course, will not be so impressive, but they will inflate. And this is the main point.

Option with detergent

The recipe is extremely simple and unpretentious.

It is not recommended to use dishwashing detergent from dishwashers!

Mix the ingredients thoroughly in the required quantity and you're done. You can blow bubbles.

Option with foam

Another simple recipe for crafting soap solution at no additional cost. You will need:

Take the ingredients, combine, mix – done! Let's blow bubbles and enjoy!

How to make soap bubbles that don't burst

If you're serious about the art of bubble blowing, it'll be helpful to learn how to make the strongest bubbles that won't burst. To prepare you will need:

Are you prepared? Great! Let's start making the solution.

Cooking method:

Take the soap and crumble it into a cup.
Add hot water. Stir until the soap is completely dissolved.
Add sugar and glycerin to the solution. We stir until victory is achieved.

A particularly strong solution has been prepared and can be used. Test in situations where ordinary bubbles would immediately burst.

Surely everyone remembers how much joy blowing soap bubbles brings! It doesn’t matter whether you are an adult or a child - the flight of balls shimmering with all the colors of the rainbow fascinates at any age. And how much grief does a child have if a magical liquid accidentally spills during the game! Usually my mother came to the rescue, knowing how to make a solution for soap bubbles at home.

Today there are many ways to prepare liquid for soap bubbles with your own hands. And knowing the composition, there is no reason to worry that this solution will damage the skin due to the use of low-quality or harmful ingredients. And it won’t be a bad idea if you involve your children in the process of preparing the fun - without a doubt, they will be delighted with it.

Liquid Recipes

The simplest options

This recipe is most often used:

baby soap - 50 g;
glycerin - 15 ml;
water - 250 ml.

Pour the soap, grated or finely crushed with a sharp knife, into hot water until completely dissolved. If it dissolves poorly, heat it without bringing it to a boil, stirring constantly. If necessary, strain through cheesecloth. Pour in some of the glycerin, mix gently and blow a soap bubble. If it doesn’t work, add a little glycerin.

It is possible to make soap bubbles at home without glycerin:

dishwashing liquid - 300 ml;
water - 300 ml;
sugar - 30 gr.

Heat the water, pour in the detergent and add granulated sugar. Stir until the sugar dissolves. The mixture is ready to use.

Recipe using liquid soap:

liquid soap - 50 ml;
water - 10 ml;
glycerin - 5 drops.

Mix the soap and water carefully, trying to prevent the formation of foam. Add glycerin. Leave the solution in a cool place for a short time.

The recipe is fragrant and safe

Bubbles often burst, and some of them may get into the baby’s eyes. We suggest replacing soap with baby shampoo, which will protect your child’s eyes from unpleasant sensations and allow him to enjoy the game “without tears.”

baby shampoo - 100 ml;
water - 200 ml;
sugar - 3 teaspoons.

Add shampoo to slightly warmed water. Leave the mixture for a day and only after that add sugar to it. This solution is completely safe for babies and also has a pleasant smell.

Recipe for soap bubbles made from glycerin:

glycerin - 1 part;
dishwashing liquid - 2 parts;
water - 6 parts.

Try to mix the ingredients so that no foam forms.

Making a solution “like from a store” is very simple:

water - 300 ml;
dishwashing detergent - 100 ml;
corn syrup - 75 ml.

This recipe will tell you how to instantly make soap bubbles at home. You just need to mix 0.3 liters of water and 0.1 liters of bath foam.

You can use shampoo or shower gel.

water - 100 ml;
shampoo (shower gel) - 100 ml;
sugar - 1 teaspoon.

Mix water and detergent and leave in the refrigerator for a week. After this period, add sugar to the solution. The prepared mixture can be used immediately after the sugar has been completely diluted.

How to make soap bubbles that don't burst

Here we need sugar syrup. To prepare it, you need to boil 1 part water and add 5 parts sugar. Cook over low heat, stirring all the time, until thickened.

water - 200 ml;
grated soap - 50 g;
sugar syrup - 25 ml;
glycerin - 100 ml.

This composition allows you to inflate soap balls that do not burst. They are so strong that it is possible to make various figures from them.

Recipe for children's parties.

water - 300 ml;
glycerin - 50 ml;
dishwashing detergent - 100 ml;
sugar - 40 gr.

Mix all the ingredients until completely dissolved, and the mixture for blowing large and durable balls is ready.

Recipes for making huge soap balls

water - 0.8 l;
glycerin - 0.1 l;
dishwashing liquid - 0.2 l;
sugar - 50 g;
gelatin - 50 gr.

Pour gelatin with water and leave to swell. Then strain and drain off excess water. Melt gelatin with sugar, avoiding boiling. Pour the resulting mixture into water, add detergent and glycerin. Mix carefully without foaming.

The solution must be prepared in a basin so that it is convenient to immerse the hoop or frame and pull out the soap balls.

It is possible to prepare a solution at home of the same quality as specialists do for their performances. To do this you will need the following ingredients:

hot water - 1 liter;
glycerin - 0.5 l;
washing powder - 100 g;
ammonia alcohol - 30 drops.

The solution should be infused for 72 hours, after which it will need to be strained and left for another 12 hours in the refrigerator.

To produce giant soap balls, they use a device made from two sticks tied together with a loop of woolen thread. The thread must be soaked in the solution and then make horizontal and vertical movements with the sticks, spreading them from side to side to different widths.

A few secrets: how to make good soap bubbles

One of the most favorite activities for any age is soap bubbles. Their recipe has long been known and is widely used by parents in order to turn a child’s everyday life into a holiday. Today on the shelves of children's stores you can find a huge number of all kinds of jars for inflating rainbow bubbles, but their composition is very questionable and unsafe for humans. Therefore, parents have to get sophisticated and look for instructions on how to make homemade ones so as not to harm the health of their child.

There are quite a few options using a variety of ingredients to prepare the desired solution. In this case, you should always strictly follow all instructions and proportions in order to make beautiful and durable soap bubbles. The recipe must be from reliable sources. Otherwise, there is a risk that nothing will work out and the children will be upset.

Main ingredients for soap solution

So, you will need the following components.

Dishwashing liquid. There is no exact brand that can be singled out as the ideal option for creating a solution for soap bubbles. It's worth trying what you use every day.
Soap. Economical is best suited.
Water. This component should be considered carefully. The water that comes out of the tap is not always good for soap bubbles. It contains too many different salts. You should first boil it and let it sit for several hours.
Glycerin solution. This is the component that is responsible for the strength, color and size of the bubble. Glycerin is sold in city pharmacies. One bottle is enough for several times. As a rule, add a teaspoon of glycerin to one liter of soap bubble solution. But there are also exceptions.

Popular recipes

Let's look at the most common options.

Recipe No. 1

The most popular and does not require special ingredients. All you need is a piece and water. These components can be found in any home. The soap should be grated on a coarse grater or cut into small pieces and dissolved in warm water. To speed up the process, the resulting mixture can be placed on low heat and stirred until a homogeneous mass is obtained.

Recipe No. 2

This is one of the easiest options for making soap bubbles at home with children. To do this you will need: 100 g of dishwashing liquid, 300 ml of water and 50 ml of glycerin. You need to mix all the ingredients. Done, you can start entertaining the kids.

You cannot use tap water because it contains too much salt, this will negatively affect the film.

Glycerin is needed to make the bubbles strong.

Recipe No. 3

For this solution making option you will need several days.

You will need: 300 ml of hot boiled water, 150 ml of glycerin, 10 drops of ammonia, 25 g of washing powder. All this must be mixed thoroughly and left alone for 2-3 days. After the time has passed, the solution must be filtered and placed in the refrigerator for 10 hours. The bubbles are very large and strong. They are no worse than those that professionals use during the holidays.

If you take the matter seriously, you can use the created liquid to create a real soap bubble show. This performance will brighten up any holiday, even if it’s an adult party; it definitely won’t be boring.

Recipe No. 4

This is an option for creating liquid to blow large bubbles.

For this you will need:

1.6 liters of water;
0.5 liters of dishwashing liquid;
0.2 l of glycerin solution;
100 g sugar;
100 g gelatin.

Gelatin is diluted in water and left to swell. Afterwards, it is necessary to strain and remove unnecessary liquid. Sugar is added to the gelatin, and the mixture is sent to the fire, heated until dissolved, but it should not be allowed to boil. All this is poured into water, then glycerin is added. The solution is mixed so that no foam occurs.

Quality checking

In order to assess whether the resulting soap solution is suitable for blowing bubbles, you need to perform some simple steps. Dip the straw into the liquid. After removal, a film should form at the end of the tube. Now we need to blow.

If at the same time small bubbles fly out, which easily scatter into thousands of small droplets, then it is worth adding a little soap solution (soap, dishwashing liquid, powder, depending on the recipe) and a certain amount of glycerin.

So, by experimenting, you can achieve

Blowing tools

The solution is clear. The main thing is to strictly follow the instructions and maintain proportions. Now it’s worth paying attention to the fact that liquid alone is not enough to get an unforgettable experience while blowing soap bubbles.

Appropriate props for soap bubbles are also required. However, it does not have to be purchased in a store. It is enough to show your imagination and follow simple instructions.

Making giant soap bubbles

There are several options here too. Let's look at them.

Tool #1

You will need: two cocktail straws, a long cord (about 1 meter).

Manufacturing method: the lace is threaded into tubes. Its ends are tied. You need to leave about 40-50 cm between the tubes. A kind of loop on the sticks should come out.

To get a giant soap bubble, you need to lower this loop with tubes into the prepared solution. At this moment, the sticks should be as close to each other as possible. After this, the tool is removed. You need to start moving the tubes in different directions so that a film forms in the loop. After this, you should guide the structure through the air, creating a huge soap bubble that will shimmer with all the colors of the rainbow. The main thing is to be able to let him fly free in time.

Tool No. 2

You will need: electrical cable, cotton cloth.

Manufacturing method: a circle with a diameter of 20-30 cm is made from the cable. Its ends are fixed with an elastic band or fishing line. The fabric is cut into strips. Then you need to wrap the cable around these sections. As a result, the solution will be absorbed into them, and it will last for a long time.

The soapy liquid is poured into a basin of the appropriate size, and the resulting hoop is placed in it. The fabric is soaked in the solution. Next is a matter of technique: you need to move this tool through the air and enjoy what you get. And whatever you want can come out: several large bubbles and one giant one, and even a whole tunnel with which you can wrap yourself and put a child in it.

Tool No. 3

You will need: a cocktail tube, a wire.

Manufacturing method: the wire is attached to a tube, creating a ring. After this, it can be given the desired shape, for example, hearts or stars. In any case, there will be unusual soap bubbles. You can use any recipe for the solution.

Tool No. 4

This is the most budget-friendly and uncomplicated prop. Thanks to it, you get not huge, but quite large soap bubbles. The cost of such an invention is zero.

You will need two hands.

Blowing method: palms are placed in a soap solution. The thumbs and index fingers form a ring through which the bubbles will fly out.

What other tools can be used to blow bubbles?

The easiest way to blow is to use a regular juice straw. There can be many of them. You can take 7 or 10 tubes and secure them with tape. The result is a wonderful device for blowing a large number of bubbles at the same time.

It’s good if you happen to have a plastic carpet beater at home. It can be used in its original form, or you can remove all connections and leave only the outer rim.

A regular funnel is suitable for blowing large bubbles. If during the process it is necessary to draw more air into the lungs, then you need to close the hole with your finger so that what happens does not disappear completely.

You can use a plastic bottle after cutting off the bottom.

Of course, a special machine for soap bubbles is also suitable, which will blow them out without human help or ingenious devices. But such mechanical “blowers” are expensive. At the same time, children are always interested in not only catching rainbow balls, but also taking an active part in their creation.

What's interesting to come up with?

Having figured out how to make homemade soap bubbles, we can consider various entertainment options.

Drawing with rainbow balls

How to make homemade soap bubbles is clear. After making them, you can do not only blowing, but also combine this process with the development of imagination and creative abilities in children. You can draw amazing things with soap bubbles and then add details to them and turn them into real masterpieces.

To do this, you will need not an ordinary soap solution, but a colored one, which is also very easy to make. To do this, add a few drops to the already prepared liquid for bubbles. After this, you can proceed directly to drawing. This is where a juice straw comes to the rescue again. You need to blow through it so that bubbles form on the surface of the soapy liquid. When the foam goes over the edge, carefully place it on a sheet of paper. You need to do this action with the number of colors that you want to see in the future painting.

You can make a foam cap and apply paper to the bubbles.

In both cases, the drawing process ends with the sheet having to dry. Then you can finish drawing what you got into a specific image, or you can leave an abstract picture. It is easy to use for greeting cards and holiday gift wrapping.

A bubble machine will also work here. If you add such a colored solution to it, bring a sheet of paper and hold it for a while, you will also get interesting patterns. The only thing worth considering is that such creativity is best done outdoors. Otherwise, you can damage the furniture or floors. In any case, children will be very interested in watching how colorful bubbles leave beautiful imprints on paper.

Unusual options

Not long ago, non-popping soap bubbles appeared on sale. They are completely safe for people and animals. They contain either gelatin or medical glue. Such bubbles do not burst in your hands; you can build pyramids from them.

If the base of the solution is then bubbles stick to your hands, but do not stick together, after them a film remains on the surface, like from PVA glue, but it is very easily removed. There are no traces left anywhere after the game, although the bubble show will be excellent, because hundreds of small transparent balls fly out at once and end up everywhere.

The gelatin base also makes interesting soap bubbles. Photos with them will turn out amazing, because you can “build” various pyramids. In the case of glycerin solutions, such structures will not work. At the same time, to prevent the soap bubble from bursting, you need to wait a few seconds.

But if you suddenly want to please your child with unpopping bubbles in the very near future, then ordinary woolen mittens or gloves will do. The effect of them will greatly surprise children. When touched with fur, the bubble does not burst, but begins to bounce off the hand, like a rubber ball from a wall. Not only children, but also adults will be captivated by playing with jumping soap bubbles.

Unpopping soap bubbles in winter

This phenomenon can be observed in winter with severe frost. When you blow soap bubbles at temperatures below zero, tiny crystals form on their surface and grow rapidly.

But in the cold you can get different soap bubbles, photos of which will surprise your friends and acquaintances. It all depends on the composition of the liquid used. For example, to get a matte finish, you need to use shampoo as a base. But the bubbles from “Fairy” will not “survive” in the snow, because they will have a more fragile structure. The blowing process itself is also important. The straw is lowered to the bottom of the glass so that the solution covers its outer side. After which the tube is slowly removed, a little foam is captured. When blowing, the straw must be twisted with smooth movements to prevent the accumulation of excess liquid, which can damage the fragile structure.

During the blowing process, foam should accumulate inside the bubble, which will prevent premature bursting. The “foam” side of the ball is placed on the snowy surface. At temperatures below 15 degrees, 10 seconds after the start of blowing, a frozen crystal ball of unprecedented beauty is obtained.